Plumbing Essentials: An Essential for When Installing a Bathtub
Plumbing Essentials: An Essential for When Installing a Bathtub
Blog Article
This article which follows about A Step-by-Step Guide to Installing a Bathtub is relatively informative. Check it out for your own benefit and decide what you think about it.
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will need a helper to vacate the old tub as well as set in the brand-new one. Make sure you have qualified yourself for the task and also fit attempting it. Instead of employing a professional to take over a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your bathroom if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your devices as well as material list ought to comprise the following:
Planning for the Installation
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain any water staying in the system. The process of removing the existing faucets can be quite troublesome because of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the tub in the needed position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bath tub up until the spirit level reviews degree.
To install taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the supply of water and also inspect all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub and also inspect the overflow electrical outlet and the typical outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and also sealing around the tub must wait till the tub has been utilized a minimum of once as this will settle it into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about issues with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are sold in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can fracture rather early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our topic on Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to browse our piece. Kindly take the opportunity to promote this blog post if you appreciated it. Thanks a bunch for your time. Don't hesitate to check up our site back soon.
Precision and quality here. Report this page